Questions? - We have the
answers
Blinking Smart Stop
- Who needs a Blinking Smart Stop?
- What does the Blinking Smart Stop do?
- How does the Blinking Smart Stop install?
- What is the difference between Blinking Smart
Stop and the Smart Stop delay version?
- Is the Blinking Smart Stop Legal?
-
What is the
difference between Blinking Smart Stop, Smart Stop Plus and Plus
3 versions?
Blinking Smart Lane Changer
- Why does my car need a Blinking Smart Lane
Changer?
- How does the Blinking Smart Lane Changer work?
- What Vehicles will the Blinking Smart Lane
Changer work on ?
- Will the Blinking Smart Lane Changer affect
the electrical system of my car ?
-
How big is the
Blinking Smart Lane Changer ?
Blinking Smart Stop
Anyone who drives a Car, Truck or an SUV. Whether
you just drive around town on your commute or you drive the
highways, motorways or the autobahn. In a recent year in the USA
alone over, 2.5 million rear-end collisions, resulted in more than
2,149 deaths that year. NHSTA has stated that an extra warning time
could prevent 90% of all rear collisions.
Studies carried out by Daimler Chrysler prove
that peoples reaction time is quicker with flashing brake lights
than without. The studies found that at a speed of 50 mph the
increased reaction time reduces the stopping distance by
approximately 14.5 feet, and at 65 mph by around 20 feet.
When you apply your brakes, depending on the
version, it causes your center high mounted (third) brake light or
main brake lights to automatically emit a visual alerting signal of 6 light
pulses, followed by steady brake light on condition.
It’s very simple, it’s a Do-It-Yourself
installation. It fits in the trunk using the labeled wires extending
from the unit. The device comes with snap in line connectors for
easy installation and fitting instructions. The average install time
for first timers is approximately 5-15 minutes. Depending on
vehicle type.
SEE INSTALLATION
VIDEO
The Delay version was designed for
those drivers who might not want to continuously flash their third
brake light when caught in bumper to bumper traffic. Once you
have applied your brakes for the first time causing your third brake
light to flash 6 times and then turn solid, touching your brakes
again within 8 seconds will cause your third brake light to turn on
normally without flashing. In other words, you must have your foot
off the brakes for more than 8 seconds before the Blinking Smart
Stop will reset and cause your third brake light to flash again.
Because laws vary from state to state and country
to country, the Blinking Smart Stop was designed to only flash the
brake lights for set amount of time (lights flash for appx. 3 seconds
and then goes solid) so they would not be confused as an emergency
indicator. We have sold products to all 50 states and twenty
five countries over the past seven years without complaints.
See Document
Blinking Smart Stop (Std) and
Blinking Smart Stop (Delay) only have
one output and were designed to attach only to the third,
center-high mounted, brake light. The Smart Stop Plus was
designed with a second output and was intended to connect directly
to the Main "Left" and "Right" brake lights of
cars and trucks with separate turn signal lights. The Smart
Stop Plus versions will not work with cars and trucks that are designed to
turn on the same "bulb" with the turn signal and brake
pedal . Plus 3 is designed to work with all brake lights
Will only work with
vehicles with separate brake light connections
Blinking Smart Stop Std & Delay versions
are compact devices, measuring
1 x
2 x 0.5 inches,
Blinking Smart Lane Changer
We have all been behind someone who never uses
their turn indicators, or whose blinker never goes off. You
become irritated and often make a dangerous maneuver to pass the
car. Alternatively, someone behind you may become irritated because
you have forgotten to use or turn off your indicator when changing
lanes. Make life easier and SAFER with BLINKING SMART, the ONE
TOUCH LANE CHANGER.
If you are a conscientious individual who cares
about your safety as well as the safety of others, than this is the
product for you.
Blinking Smart is a small microprocessor based
unit that monitors the turn indicator circuits to turn them on if
the switch has been touched momentarily. If it sees a
momentary signal, it will flash the indicator lights an additional 6
times.
No more holding and keeping your fingers on your
turn switch when changing lanes.
Blinking Smart works on most vehicles that have
separate rear brake and indicator lights.
Cars, such as some Fords, use the same light bulb
for both the brake and rear indicator lights. In these types of
vehicles, the front and rear indicator circuits on each side are
controlled with separate signals. If installed on the rear
indicator circuits, Blinking Smart will not be able to control the
front indicators or the dashboard lights.
We have all been behind someone who never uses their turn
indicators, or whose blinker never goes off. You become
irritated and often make a dangerous maneuver to pass the car.
Alternatively, someone behind you may become irritated because you
have forgotten to use or turn off your indicator when changing
lanes. Make life easier and SAFER with BLINKING SMART, the ONE
TOUCH LANE CHANGER.
If you are a conscientious individual who cares about your safety
as well as the safety of others, than this is the product for you.
Blinking Smart is a small microprocessor based unit that monitors
the turn indicator circuits to turn them on if the switch has been
touched momentarily. If it sees a momentary signal, it will
flash the indicator lights an additional 6 times.
No more holding and keeping your fingers on your turn switch when
changing lanes.
Blinking Smart works on most vehicles that have
separate rear brake and indicator lights.
Cars, such as some Fords, use the same light bulb
for both the brake and rear indicator lights. In these types of
vehicles, the front and rear indicator circuits on each side are
controlled with separate signals. If installed on the rear
indicator circuits, Blinking Smart will not be able to control the
front indicators or the dashboard lights.
No! Blinking Smart is a very low power
consumption device that attaches to the existing turn indicator
circuit so there are no wires to cut. It's microprocessor
draws about the same amount of power as the dashboard clock so your
vehicles Engine Control Unit (ECU) will never know that the Blinking
Smart is there.
Blinking Smart Lane Changer is a compact device, measuring 2 x
2 x 0.75 inches, including the mounting attachment.
|
