Smart Stop Plus Installation Guide

 
 
Install Instructions for:
Blinking Smart Stop Plus , Plus Delay , Plus 3 and Plus 3 Delay
 
You do not need to be Technical to install these products
Tools Reqd.
Screwdriver, pliers/cutters 
Difficulty rating scale 2 out of 10

I. Description

Applying your brakes will cause your existing 2 main brake lights to blink rapidly 6 times and then stay on solid as long as you have your foot on the brake pedal. Only works with  vehicles with separate brake light connections.

   II. Features

  • Size: 1" x 2" x 0.5" (26mm x 51mm x 13mm)

  • Operating Voltage: 12 Volts DC

  • Operating Temp: -30șC to +70șC

  • Max Power Rating 30amps

  • Max Power Consumption: 1W

   III. Circuit Diagram

   IV. Installation

  1. Locate access to and identify the brake light wires. The easiest way to access them is from where you change the existing bulbs. Choose one side (left or right) to start from.

  2. Place a “Quick Connect” connector over positive (+) side wire going to the first brake light at least 3 inches from the light and insert the Red wire. Using the pliers, squeeze the metal splice to secure the wires and then snap the cover closed.

  3. Place a second “Quick Connect” connector over the same wire between the first one and the brake light and insert the shorter Blue wire. Squeeze and snap as in step 2.

  4. Cut the positive (+) brake light wire between the location of the 2 “Quick Connect” connectors..

  5. Place a “Quick Connect” connector over negative (-) side wire of the brake light (or any chassis “GND” connection) and insert the Black wire. Squeeze and snap as in step 2.

  6. Run the longer blue wire over to the location of the other brake light.

  7. Cut the positive (+) side wire of the second brake light. Leave at least 2 inches.

  8. Place a “Quick Connect” connector over the exposed wire still attached to the light and
    insert the blue wire. Squeeze and snap as in step 2.

  9. Locate the Blinking Smart Stop inside somewhere away from areas of high temperature, moisture
    and water leakage.

Installation Blinking Smart Stop Plus 3 and Plus 3 Delay

    I. Description

Applying your brakes will cause your existing all brake lights to blink rapidly approximately 4 times and then stay on solid as long as you have your foot on the brake pedal. Works with all vehicles with separate brake light connections.

   II. Features

  • Size: 1" x 2" x 0.5" (26mm x 51mm x 13mm)

  • Operating Voltage: 12 Volts DC

  • Operating Temp: -30șC to +70șC

  • Max Power Rating 30amps

  • Max Power Consumption: 1W

   III. Circuit Diagram

   IV. Installation

1) Locate access to and identify the brake light wires. The easiest way to access them is from where you change the existing bulbs. Choose one side (left or right) to start from.

2) Place a “Quick Connect” connector over positive (+) side wire going to the first brake light at least 3 inches from the light and insert the short Red wire. Using the pliers, squeeze the metal splice to secure the wires and then snap the cover closed.

3) Place a second “Quick Connect” connector over the same wire between the first one and the brake light and insert the shorter Blue wire. Squeeze and snap as in step 2.

4) Cut the positive (+) brake light wire between the location of the 2 “Quick Connect” connectors.

5) Place a “Quick Connect” connector over negative (-) side wire of the brake light (or any chassis “GND” connection) and insert the Black wire. Squeeze and snap as in step 2.

6) Run the longer blue wire over to the location of the other brake light.

7) Cut the positive (+) side wire of the second brake light. Leave at least 2 inches.

8) Place a “Quick Connect” connector over the exposed wire still attached to the light and insert theblue wire. Squeeze and snap as in step 2.

9) Locate access to and identify the third brake light wires.

10) Follow the instructions in steps 2, 3, and 4 for connecting to the third brake light using the “long red” and yellow wires.

11) Secure the Smart Stop inside somewhere away from areas of high temperature, moisture and water.

1) Locat)

Click here to view pdf version.

  
 

Give yourself a chance, avoid becoming a victim and a statistic.

Copyright © 2006,  Kahtec Technologies International.  All rights reserved.  l  Privacy Policy - Site Map

For auto safety accessories, Lighting and other Laws vary from state to state and country to country.  Kahtec Technologies Int. makes no representation or warranty to the legality of its products for street use on any vehicle or in any location.
Design By Webs From Us